Camera Mount On Shoei Rf-1200?

[JScrambler]

Anyone else out there have this helmet? I'm having trouble finding a mounting location. This helmet have angles along the areas that would normally be smooth. Which is keeping the gopro mount from sticking to the surface.

 

[Hippo-Drones]

If you buy some 3M sticky pads you could cut them into strips and pad out the gopro sticky pad to fill the ripples?

 

[JScrambler]

If you buy some 3M sticky pads you could cut them into strips and pad out the gopro sticky pad to fill the ripples?

I will try that. Thank you.

 

[Lurch]

Is that the same as an NSR?

 

[MIcruiser]

I have mine right of center, with a couple arm pieces to put the camera right in front.

 

[Lurch]

What's that bit about then?

 

[MIcruiser]

thats the new buckles that they sell. the grey rubber piece is what they use instead of the white lock that needs to be tethered to a screw. Its all part of the buckle now. I like it a lot more. It blends in with the rest of the system and you can use a M4 bolt instead of the giant thumb screws that come with the mounts.

 

[SonicMoto]

Friend of mine Sp3aK got the 1200 and mounts his the same as he used to, same as I do.

Make a custom mold via JB Weld Plastic weld putty
http://aminoapps.com/page/motorcycle-amino/9090910/how-to-chin-mount-a-gopro

 

[WingManGT]

Just use sugru. It works quite well.

 

[JScrambler]

Thank you for the tips everyone.

 

[JScrambler]

I found this 3D printed mount just for the rf-1200 chin.

https://www.shapeways.com/product/5LXTCDPJS/gopro-chin-mount-shoei-rf-1200?optionId=62732482

 

[shift_love]

i used a modified mount and extra tape for the chin for awhile, but it was a little wiggly, and ended up coming loose once. so i decided to relocate it to the side and use a bunch of adapters, its the best spot at the moment. but i really like this photo above my post...more money to spend i guess

 

[KittenMeat]

Hellmounts makes the mount that I use. I'll do a little review of it once I get moved into the new place.

http://www.hellmounts.com/

 

[shift_love]

Hellmounts makes the mount that I use. I'll do a little review of it once I get moved into the new place.

its the same one that was posted from that 3d printing site. i went ahead and bought one when seeing this thread. they look good

 

[illproducr]

Awesome, that 3D printed mount is just what I need. I ordered one. Ditching my side mount of hinges and bolts for this.

 

[Hippo-Drones]

You can get a 3D printed offset bracket too which would work great with that mount and would allow the camera lens to be bang center on your chin!

 

[Superballs]

I have my setup shown in the "show your setup" thread that's bouncing around here somewhere.

I don't get TOO much wind noise with my setup, but it does hold my visor open a crack...which I don't mind and it covers my vents in front, but I have an HJC CL16 and the vents are more decorative than anything anyway.

 

[Hippo-Drones]

This is about a specific skid lid SB

 

[Superballs]

The one I have will fit any lid with a chin bar.

This one.

Of course, it's not as tidy as the 3D printed one, but you can remove it and put it on a new helmet much more easily.

 

[Raoul Duke]

its the same one that was posted from that 3d printing site. i went ahead and bought one when seeing this thread. they look good

Woah, no they are definitely not the same. I bought one of Disillusioned's mounts and it didn't fit right, and didn't come with a pad. Lead time was terrible and there was little communication. THEN I bought one from Rob over at HellMounts... Totally different product. Came with a pad, they said it's warrantied, and it fits way better on the helmet than the Shapeways mount did.

I'd buy another one from HellMounts in a minute if they made one for my RPHA 11 also